Protec FRP Membrane Pressure Vessels

protec_vessels

Shown are the different Protec Arisawa FRP membrane pressure vessels and models available through So Pure Enterprises.

This is a traditional vessel design with feed and concentrate connections placed in the end closure of the vessel head.

Product Overview The models are designed for continuous use as housing for membrane filtration elements to purify typical waters at any positive pressure up to 1000 PSI. The design will accommodate any make of four-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped.

Models & PDF Engineerial Drawings:

This side ported vessel has feed and concentrate connections found in the side wall of the vessel shell.

Product Overview The models are designed for continuous use as housing for membrane filtration elements to purify typical brackish waters at any positive pressure up to 450 PSI. The design will accommodate any make of four-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped.

Models & PDF Engineerial Drawings:

This is a traditional vessel design with feed and concentrate connections located in the end closure of the vessel head.

The models are designed for continuous use as housing for membrane filtration elements to purify waters at any positive pressure up to 1200 PSI. The design will accommodate any make of eight-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped. Models with a PSI of 150-600 purify typical brackish waters while models with a PSI of 1000-1200 purify typical seawater.

Models & PDF Engineerial Drawings:

This side ported vessel has feed and concentrate connections located in the side wall of the vessel shell.

The models are designed for continuous use as housing for membrane filtration elements to purify waters at any positive pressure up to 1200 PSI. The design will accommodate any make of eight-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped. Models with a PSI of 75-600 purify typical brackish waters while models with a PSI of 1000-1200 purify typical seawater.

Models & PDF Engineerial Drawings:

This design provides over 50% more flow and can also reduce pressure-drop to decrease system operation costs.

The models are designed for continuous use as housing for membrane filtration elements to purify waters at any positive pressure up to 1200 PSI. What separates these MSP models from the traditional side port is the addition of the 3” or 4” port designed specifically for systems using multiple port technology. The design will accommodate any make of eight-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped. Models with a PSI of 75-600 purify typical brackish waters while models with a PSI of 1000-1200 purify typical seawater.

Models & PDF Engineerial Drawings:

This is a traditional vessel design with feed and concentrate connections placed in the end closure of the vessel head.

The models are designed for continuous use as housing for membrane filtration elements to purify waters at any positive pressure up to 1200 PSI. The design will accommodate any make of nine-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped. Models with a PSI of 300-600 purify typical brackish waters while models with a PSI of 1000-1200 purify typical seawater.

Models

Please contact us to know the products that are available or that we can develop for you.

This is a traditional vessel design with feed and concentrate connections placed in the end closure of the vessel head.

The models are designed for continuous use as housing for membrane filtration elements to purify waters at any positive pressure up to 1200 PSI. The design will accommodate any make of nine-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped. Models with a PSI of 300-600 purify typical brackish waters while models with a PSI of 1000-1200 purify typical seawater.

Models

Please contact us to know the products that are available or that we can develop for you.

This design provides over 50% more flow and can also reduce pressure-drop to decrease system operation costs.

The models are designed for continuous use as housing for membrane filtration elements to purify waters at any positive pressure up to 1200 PSI. What separates these MSP models from the traditional side port is the 3” port designed specifically for systems using multiple port technology. The design will accommodate any make of eight-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped. Models with a PSI of 300-600 purify typical brackish waters while models with a PSI of 1000-1200 purify typical seawater.

Models

Please contact us to know the products that are available or that we can develop for you.

This is a traditional vessel design with feed and concentrate connections located in the end closure of the vessel head.

The models are designed for continuous use as housing for membrane filtration elements to purify waters at any positive pressure up to 1200 PSI. The design will accommodate any make of sixteen-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped. Models with a PSI of 300-600 purify typical brackish waters while models with a PSI of 1000-1200 purify typical seawater.

Models

Please contact us to know the products that are available or that we can develop for you.

This side ported vessel has feed and concentrate connections located in the side wall of the vessel shell.

The models are designed for continuous use as housing for membrane filtration elements to purify waters at any positive pressure up to 1200 PSI. The design will accommodate any make of sixteen-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel. The models have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped. Models with a PSI of 300-600 purify typical brackish waters while models with a PSI of 1000-1200 purify typical seawater.

Models

Please contact us to know the products that are available or that we can develop for you.

Seawater desalination plants using Reverse Osmosis (RO) typically use large diameter metal pipes to feed and collect concentrate to and from the FRP membrane pressure vessels. As seawater is highly corrosive, these pipes are typically made of expensive materials like super stainless steel or super duplex materials. Protec Arisawa has developed an innovative system using fiber reinforced plastic (FRP) to economically replace the expensive high grade metal piping.

Product Information PDF